View TS128MDOM40V-S_4628063.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 1 description with an ide interface and strong data retention ability, 40-pin ide flash modules are ideal for use in the harsh environments where industrial pcs, set-top boxes, etc. are used. placement features ? rohs compliant products ? storage capacity: 128mb ~ 16gb ? operating voltage: 3.3v 5% or 5v 10% ? operating temperature: 0c ~ 70c ? endurance: 2,000,000 program/erase cycles ? mtbf: 1,000,000 hours ? durability of connector: 10,000 times ? fully compatible with devices and os that support the ide standard (pitch = 2.54mm) ? built-in ecc function assure s high reliability of data transfer ? supports up to ultra dma mode 4 ? supports pio mode 6 ? support wear-leveling to extend product life dimensions side millimeters inches a 61.00 0.40 2.402 0.016 b 27.10 0.50 1.067 0.020 c 7.10 0.20 0.280 0.008
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 2 pin assignments pin no. pin name pin no. pin name pin no. pin name pin no. pin name 01 -reset 11 hd3 21 dmarq 31 ireq 02 gnd 12 hd12 22 gnd 32 iois16b 03 hd7 13 hd2 23 iowb 33 ha1 04 hd8 14 hd13 24 gnd 34 pdiagb 05 hd6 15 hd1 25 iorb 35 ha0 06 hd9 16 hd14 26 gnd 36 ha2 07 hd5 17 hd0 27 iordy 37 ce1b 08 hd10 18 hd15 28 nc 38 ce2b 09 hd4 19 gnd 29 -dmack 39 daspb 10 hd11 20 vcc 30 gnd 40 gnd pin definition symbol function hd0 ~ hd15 data bus (bi-directional) ha0 ~ ha2 address bus (input) -reset device reset (input) iorb device i/o read (input) iowb device i/o write (input) iois16b transfer type 8/16 bit (output) ce1b, ce2b chip select (input) pdiagb pass diagnost ic (bi-directional) daspb disk active/slave present (bi-directional) dmarq dma request dmack- dma acknowledge ireq interrupt request (output) nc no connection gnd ground vcc vcc power input input power the 40-pin ide flash module offers 2 ways to get input power, either via the small power cord or through pin 20 of the ide connector. if pin 20 of the ide connector is defined as nc (no connect), then the 40-pin ide flash module must be directly connected to your system?s power supply. if pin 20 of the ide connector is defined as vcc, then the 40-pin ide flash module can get necessary power without use of the power cord. pin layout pin1 pin39 bulge pin2 pin40
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 3 block diagram with 1 pcs of flash memory: with 2 pcs of flash memory:
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 4 absolute maximum ratings symbol parameter min max unit vdd-vss dc power supply -0.6 +6 v ta operating temperature 0 +70 c tst storage temperature -40 +85 c recommended operating conditions symbol parameter min max units vdd power supply 3.0 5.5 v vin input voltage 0 vdd+0.3 v ta operating temperature 0 +70 c dc characteristics (ta=0 o c to +70 o c, vcc = 5.0v 10%) parameter symbol min max unit remark supply voltage v cc 4.5 5.5 v high level output voltage v oh v cc -0.8 -- v low level output voltage v ol -- 0.8 v 4.0 -- v non-schmitt trigger high level input voltage v ih 2.92 -- v schmitt trigger 1 -- 0.8 v non-schmitt trigger low level input voltage v il -- 1.70 v schmitt trigger 1 (ta=0 o c to +70 o c, vcc = 3.3v 5%) parameter symbol min max unit remark supply voltage v cc 3.135 3.465 v high level output voltage v oh v cc -0.8 -- v low level output voltage v ol -- 0.8 v 2.4 -- v non-schmitt trigger high level input voltage v ih 2.05 -- v schmitt trigger 1 -- 0.6 v non-schmitt trigger low level input voltage v il -- 1.25 v schmitt trigger 1
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 5
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 6 true ide pio mode read/write timing item mode 0 mode 1 mode 2 mode 3 mode 4 mode 5 mode 6 t 0 cycle time (min) 1 600 383 240 180 120 100 80 t 1 address valid to -iord/-iowr setup (min) 70 50 30 30 25 15 10 t 2 -iord/-iowr (min) 1 165 125 100 80 70 65 55 t 2 -iord/-iowr (min) register (8 bit) 290 290 290 80 70 65 55 t 2i -iord/-iowr recovery time (min) -- -- -- 70 25 25 20 t 3 -iowr data setup (min) 60 45 30 30 20 20 15 t 4 -iowr data hold (min) 30 20 15 10 10 5 5 t 5 -iord data setup (min) 50 35 20 20 20 15 10 t 6 -iord data hold (min) 5 5 5 5 5 5 5 t 6z -iord data tristate (max) 2 30 30 30 30 30 20 20 t 7 address valid to iocs16 assertion (max) 4 90 50 40 n/a n/a n/a n/a t 8 address valid to iocs16 released (max) 4 60 45 30 n/a n/a n/a n/a t 9 -iord/-iowr to address valid hold 20 15 10 10 10 10 10 t rd read data valid to iordy active (min), if iordy initially low after ta 0 0 0 0 0 0 0 t a iordy setup time 3 35 35 35 35 35 n/a 5 n/a 5 t b iordy pulse width (max) 1250 1250 1250 1250 1250 n/a 5 n/a 5 t c iordy assertion to release (max) 5 5 5 5 5 n/a 5 n/a 5 notes: all timings are in nanoseconds. the maximum l oad on -iocs16 is 1 lsttl with a 50 pf (40pf below 120nsec cycle time) total load. all times are in nanos econds. minimum time from -iordy high to -iord high is 0 nsec, but minimum -iord width shall still be met. (1) t 0 is the minimum total cycle time, t 2 is the minimum command active time, and t 2i is the minimum command recovery time or command inactive time. t he actual cycle time equals the sum of the actual command active time and the actual command inactive time. the three timing requirements of t0, t 2 , and t 2i shall be met. the minimum total cycle time requirement is greater than the sum of t 2 and t 2i . this means a host implementation can lengthen either or both t 2 or t 2i to ensure that t 0 is equal to or greater than the value reported in the device?s identify device data. (2) this parameter specifies the time from the negati on edge of -iord to the time that the data bus is released by the device. (3) the delay from the activation of -iord or -iowr unt il the state of iordy is first sampled. if iordy is inactive then the host shall wait until iordy is active before the pio cycle can be completed. if the device is not driving iordy negated at t a after the activation of -iord or -iowr, then t 5 shall be met and t rd is not applicable. if the device is driving iordy negated at the time t a after the activation of -iord or -iowr, then t rd shall be met and t5 is not applicable. (4) t 7 and t 8 apply only to modes 0, 1 and 2. for other modes, this signal is not valid. (5) iordy is not supported in this mode.
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 7 true ide pio mode timing diagram figure 1: true ide pio mode timing diagram notes: (1) device address consists of -cs0, -cs1, and a[02::00] (2) data consists of d[15::00] (16-bit) or d[07::00] (8 bit) (3) -iocs16 is shown for pio modes 0, 1 and 2. for other modes, this signal is ignored. (4) the negation of iordy by the device is used to extend the pio cycle. the determination of whether the cycle is to be extended is made by the host after t a from the assertion of -iord or -iowr. the assertion and negation of iordy is described in the following three cases: (4-1) device never negates iordy: no wait is generated. (4-2) device starts to drive iordy low before t a , but causes iordy to be asserted before t a : no wait generated. (4-3) device drives iordy low before t a : wait generated. the cycle completes after iordy is reasserted. for cycles where a wait is generated and -iord is asserted, the device shall place read data on d15-d00 for t rd before causing iordy to be asserted.
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 8 true ide multiword dma mode re ad/write timing specification item mode 0 (ns) mode 1 (ns) mode 2 (ns) mode 3 (ns) mode 4 (ns) t 0 cycle time (min) 1 480 150 120 100 80 t d -iord / -iowr asserted width(min) 1 215 80 70 65 55 t e -iord data access (max) 150 60 50 50 45 t f -iord data hold (min) 5 5 5 5 5 t g -iord/-iowr data setup (min) 100 30 20 15 10 t h -iowr data hold (min) 20 15 10 5 5 t i dmack to ?iord/-iowr setup (min) 0 0 0 0 0 t j -iord / -iowr to -dmack hold (min) 20 5 5 5 5 t kr -iord negated width (min) 1 50 50 25 25 20 t kw -iowr negated width (min) 1 215 50 25 25 20 t lr -iord to dmarq delay (max) 120 40 35 35 35 t lw -iowr to dmarq delay (max) 40 40 35 35 35 t m cs(1:0) valid to ?iord / -iowr 50 30 25 10 5 t n cs(1:0) hold 15 10 10 10 10 t z -dmack 20 25 25 25 25 notes: (1) t 0 is the minimum total cycle time and t d is the minimum command active time, while t kr and t kw are the minimum command recovery time or command inactive time for input and output cycles respectively. the actual cycle time equals the sum of the actual comm and active time and the actual command inactive time. the three timing requirements of t 0 , t d , t kr , and t kw shall be met. the minimum total cycle time requirement is greater than the sum of t d and t kr or t kw .for input and output cycles respectively. this means a host implementation can lengthen either or both of t d and either of t kr , and t kw as needed to ensure that t 0 is equal to or greater than the value report ed in the device?s identify device data.
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 9 true ide multiword dma mode read/write timing diagram figure 2: true ide multiword dma mode read/write timing diagram notes: (1) if the card cannot sustain continuous, minimum cycl e time dma transfers, it may negate dmarq within the time specified from the start of a dma transfer cycle to suspend the dma transfers in progress and reassert the signal at a later time to continue the dma operation. (2) this signal may be negated by the host to suspend the dma transfer in progress.
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 10 ultra dma mode read/write timing specification ultra dma is an optional data transfer protocol used with the read dma, and write dma, commands. when this protocol is enabled, the ultra dma protocol shall be used instead of the multiword dma protocol when these commands are issued by the host. this protocol applies to the ultra dma data burst only. when this protocol is used there are no changes to other elements of the ata protocol. udma signal type true ide mode udma dmarq output dmarq dmack input -dmack stop input stop 1 hdmardy(r) hstrobe(w) input -hdmardy 1,2 hstrobe(w) 1,3,4 ddmardy(w) dstrobe(r) output -ddmardy(w) 1,3 dstrobe(r) 1,2,4 data bidir d[15:00] address input a[02:00] 5 csel input -csel intrq output intrq card select input -cs0 -cs1 notes: 1) the udma interpretation of this signal is valid only during an ultra dma data burst. 2) the udma interpretation of this signal is valid only during and ultra dma data burst during a dma read command. 3) the udma interpretation of this si gnal is valid only during an ultra dma data burst during a dma write command. 4) the hstrobe and dstrobe signals are active on both the rising and the falling edge. 5) address lines 03 through 10 are not used in true ide mode. several signal lines are redefined to provide different functions during an ultra dma data burst. these lines assume their udma definitions when: 1. an ultra dma mode is selected, and 2. a host issues a read dma, or a write dma command requiring data transfer, and 3. the device asserts (-)dmarq, and 4. the host asserts (-)dmack. these signal lines revert back to the definitions used for non-ultra dma transfers upon the negation of -dmack by the host at the termination of an ultra dma data burst. with the ultra dma protocol, the strobe signal that latches data from d[15:00] is generated by the
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 11 same agent (either host or device) that drives the data onto the bus. ownership of d[15:00] and this data strobe signal are given either to the device during an ultra dma data-in burst or to the host for an ultra dma data-out burst. during an ultra dma data burst a sender shall always drive data onto the bus, and, after a sufficient time to allow for propagation delay, cable settling, and setup time, the sender shall generate a strobe edge to latch the data. both edges of strobe are used for data transfers so that the frequency of strobe is limited to the same frequency as the data. words in the identify device data indicate support of the ultra dma feature and the ultra dma modes the device is capable of supporting. the set transfer mode subcommand in the set features command shall be used by a host to select the ultra dma mode at which the system operates. the ultra dma mode selected by a host shall be less than or equal to the fastest mode of which the device is capable. only one ultra dma mode shall be selected at any given time. all timing requirements for a selected ultra dma mode shall be satisfied. devices supporting any ultra dma mode shall also support all slower ultra dma modes. an ultra dma capable device shall retain the previously selected ultra dma mode after executing a software reset sequence or the sequence caused by receipt of a device reset command if a set features disable reverting to defaults command has been issued. the device may revert to a multiword dma mode if a set features enable reverting to default has been issued. an ultra dma capable device shall clear any previously selected ultra dma mode and revert to the default non-ultra dma modes after executing a power-on or hardware reset. both the host and device perform a crc function during an ultra dma data burst. at the end of an ultra dma data burst the host sends its crc data to the device. the device compares its crc data to the data sent from the host. if the two values do not match, the device reports an error in the error register. if an error occurs during one or more ultra dma data bursts for any one command, the device shall report the first error that occurred. if the device detects that a crc error has occurred before data transfer for the command is complete, the device may complete the transfer and report the error or abort the command and report the error. note ? if a data transfer is terminated before completion, the assertion of intrq should be passed through to the host software driver regardless of whether all data requested by the command has been transferred.
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 12 ultra dma data burs t timing requirements udma mode 0 udma mode 1 udma mode 2 udma mode 3 udma mode 4 name min max min max min max min max min max measure location (see note 2) t 2cyctyp 240 160 120 90 60 sender t cyc 112 73 54 39 25 note 3 t 2cyc 230 153 115 86 57 sender t ds 15.0 10.0 7.0 7.0 5.0 recipient t dh 5.0 5.0 5.0 5.0 5.0 recipient t dvs 70.0 48.0 31.0 20.0 6.7 sender t dvh 6.2 6.2 6.2 6.2 6.2 sender t cs 15.0 10.0 7.0 7.0 5.0 device t ch 5.0 5.0 5.0 5.0 5.0 device t cvs 70.0 48.0 31.0 20.0 6.7 host t cvh 6.2 6.2 6.2 6.2 6.2 host t zfs 0 0 0 0 0 device t dzfs 70.0 48.0 31.0 20.0 6.7 sender t fs 230 200 170 130 120 device t li 0 150 0 150 0 150 0 100 0 100 note 4 t mli 20 20 20 20 20 host t ui 0 0 0 0 0 host t az 10 10 10 10 10 note 5 t zah 20 20 20 20 20 host t zad 0 0 0 0 0 device t env 20 70 20 70 20 70 20 55 20 55 host t rfs 75 70 60 60 60 sender t rp 160 125 100 100 100 recipient t iordyz 20 20 20 20 20 device t ziordy 0 0 0 0 0 device t ack 20 20 20 20 20 host t ss 50 50 50 50 50 sender notes: all timings in ns (1) all timing measurement switching points (low to high and high to low) shall be taken at 1.5 v. (2) all signal transitions for a timing parameter shall be measured at the connector specified in the measurement location column. for example, in the case of t rfs , both strobe and -dmardy transitions are measured at the sender connector. (3) the parameter t cyc shall be measured at the recipient?s connector farthest from the sender. (4) the parameter t li shall be measured at the connector of the sender or recipient that is responding to an incoming transition from the recipient or sender respectively. both the incoming signal and the outgoing response shall be measured at the same connector. (5) the parameter t az shall be measured at the connector of the sender or recipient that is driving the bus but must release the bus to allow for a bus turnaround. (6) see page 14 the ac timing requirements in ultra dma ac signal requirements.
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 13 ultra dma data burst timing descriptions name comment notes t 2cyctyp typical sustained average two cycle time t cyc cycle time allowing for asymmetry and clock variations (from strobe edge to strobe edge) t 2cyc two cycle time allowing for clock variations (from rising edge to next rising edge or from falling edge to next falling edge of strobe) t ds data setup time at recipient (from data valid until strobe edge) 2, t dh data hold time at recipient (from strobe edge until data may become invalid) 2, t dvs data valid setup time at sender (from data valid until strobe edge) 3 t dvh data valid hold time at sender (from strobe edge until data may become invalid) 3 t cs crc word setup time at device 2 t ch crc word hold time device 2 t cvs crc word valid setup time at host (from crc valid until -dmack negation) 3 t cvh crc word valid hold time at sender (from -dmack negation until crc may become invalid) 3 t zfs time from strobe output released-to-driving until the first transition of critical timing. t dzfs time from data output released-to-driving unt il the first transition of critical timing. t fs first strobe time (for device to first negat e dstrobe from stop during a data in burst) t li limited interlock time 1 t mli interlock time with minimum 1 t ui unlimited interlock time 1 t az maximum time allowed for output drivers to release (from asserted or negated) t zah minimum delay time required for output t zad drivers to assert or negate (from released) t env envelope time (from -dmack to stop a nd -hdmardy during data in burst initiation and from dmack to stop during data out burst initiation) t rfs ready-to-final-strobe time (no strobe edg es shall be sent this long after negation of -dmardy) t rp ready-to-pause time (that recipient sha ll wait to pause after negating -dmardy) t iordyz maximum time before releasing iordy t ziordy minimum time before driving iordy 4, t ack setup and hold times for -dmack (before assertion or negation) t ss time from strobe edge to negation of dm arq or assertion of stop (when sender terminates a burst) notes: (1) the parameters t ui , t mli (in page 19: ultra dma data-in burst device termination timing and page 20: ultra dma data-in burst host termination timing), and t li indicate sender-to-recipient or recipient-to-sender interlocks,i.e., one agent (either sender or recipient) is waiting for the other agent to respond with a signal before proceeding.t ui is an unlimited interlock that has no maximum time value. t ml i is a limited time-out that has a defined minimum. t li is a limited time-out that has a defined maximum. (2) 80-conductor cabling (see see ata specification :annex a)) shall be required in order to meet setup (t ds , t cs ) and hold (t dh , t ch ) times in modes greater than 2. (3) timing for t dvs , t dvh , t cvs and t cvh shall be met for lumped capacitive loads of 15 and 40 pf at the connector where the data and strobe signals have the same capacitive load value. due to reflections on the cable, these timing measurements are not valid in a normally functioning system. (4) for all timing m odes the parameter t ziordy may be greater than t env due to the fact that the host has a pull-up on iordy- giving it a known state when released.
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 14 ultra dma sender and recipi ent ic timing requirements udma mode 0 (ns) udma mode 1 (ns) udma mode 2 (ns) udma mode 3 (ns) udma mode 4 (ns) name min max min max min max min max min max t dsic 14.7 9.7 6.8 6.8 4.8 t dhic 4.8 4.8 4.8 4.8 4.8 t dvsic 72.9 50.9 33.9 22.6 9.5 t dvhic 9.0 9.0 9.0 9.0 9.0 t dsic recipient ic data setup time (from data valid until strobe edge) (see note 2) t dhic recipient ic data hold time (from strobe edge until data may become invalid) (see note 2) t dvsic sender ic data valid setup time (from data valid until strobe edge) (see note 3) t dvhic sender ic data valid hold time (from strobe edge until data may become invalid) (see note 3) notes: (1) all timing measurement switching points(low to high and high to low) shall be taken at 1.5 v. (2) the correct data value shall be captured by the recipi ent given input data with a slew rate of 0.4 v/ns rising and falling and the input strobe with a slew rate of 0.4 v/ns rising and falling at t dsic and t dhic timing (as measured through 1.5 v). (3) the parameters t dvsic and t dvhic shall be met for lumped capacitive loads of 15 and 40 pf at the ic where all signals have the same capacitive load value. noise that may couple onto the output signals from external sources has not been included in these values. ultra dma ac signal requirements name comment min[v/ns] max [v/ns] note s rise rising edge slew rate for any signal 1.25 1 s fall falling edge slew rate for any signal 1.25 1 note: (1) the sender shall be tested while driving an 18 inch long, 80 conductor cable with pvc insulation material. the signal under test shall be cut at a test point so that it has not trace, cable or recipient loading after the test point. all other signals should remain connected through to the recipient. the test point may be located at any point between the sender?s series termination resistor and one half inch or less of conductor exiting the connector. if the test point is on a cable conductor rather than the pcb, an adjacent ground conductor shall also be cut within one half inch of the connector. the test load and test points should then be soldered di rectly to the exposed source side connectors. the test loads consist of a 15 pf or a 40 pf, 5%, 0.08 inch by 0.05 inch surface mount or smaller size capacitor from the test point to ground. slew rates shall be met for both capacitor values. measurements shall be taken at the test point using a <1 pf, >100 kohm, 1 ghz or faster probe and a 500 mhz or faster oscilloscope. the average rate shall be measured from 20% to 80% of the settled voh level with data transitions at least 120 nsec apart. the settled voh level shall be measured as the average output high level under the defined testing conditions from 100 nsec after 80% of a rising edge until 20% of the subsequent falling edge.
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 15 initiating an ultra dma data-in burst (a) an ultra dma data-in burst is initiated by following the steps lettered below. the timing diagram is shown in below: ultra dma data-in burst initiation timing. the associated timing parameters are specified in page 12: ultra dma data burst timing requirements and are described in page 13: ultra dma data burst timing descriptions. (b) the following steps shall occur in the order they are listed unless otherwise specifically allowed: (c) the host shall keep -dmack in the negated state before an ultra dma data burst is initiated. (d) the device shall assert dmarq to initiate an ultra dma data burst. after assertion of dmarq the device shall not negate dmarq until after the first negation of dstrobe. (e) steps (c), (d), and (e) may occur in any order or at the same time. the host shall assert stop. (f) the host shall negate -hdmardy. (g) in true ide mode, the host shall not assert -cs0, -cs1 and a[02:00]. (h) steps (c), (d), and (e) shall have occurred at least t ack before the host asserts -dmack. the host shall keep -dmack asserted until the end of an ultra dma data burst. (i) the host shall release d[15:00] within t az after asserting -dmack. (j) the device may assert dstrobe t ziordy after the host has asserted -dmack. while operating in true ide mode, once the device has driven dstrobe, the device shall not release dstrobe until after the host has negated -dmack at the end of an ultra dma data burst. (k) the host shall negate stop and assert -hdmardy within t env after asserting -dmack. after negating stop and asserting -hdmardy, the host shall not change the state of either signal until after receiving the first transition of dstrobe from the device (i.e., after the first data word has been received). (l) the device shall drive d[15:00] no sooner than t zad after the host has asserted -dmack, negated stop, and asserted -hdmardy. (m) the device shall drive the first word of the data transfer onto d[15:00]. this step may occur when the device first drives d[15:00] in step (j). (n) to transfer the first word of data the device shall negate dstrobe within t fs after the host has negated stop and asserted -hdmardy. the device shall negate dstrobe no sooner than t dvs after driving the first word of data onto d[15:00].
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 16 all waveforms in this diagram are sh own with the asserted state high. negative true signals appear inverted on the bus relative to the diagram. notes: the definitions for the iordy:-ddmardy:dstrobe , -iord: -hdmardy:hstrobe, and -iowr:stop signal lines are not in effect until dmarq and -dmack are asserted. a[02:00], -cs0 & -cs1 are true ide mode signal definitions.
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 17 sustaining an ultra dma data-in burst an ultra dma data-in burst is sustained by following the steps lettered below. the timing diagram is shown in below: sustained ultra dma data-in burst timing. the timing parameters are specified in page 12: ultra dma data burst timing requirements and are described in page 13: ultra dma data burst timing descriptions. the following steps shall occur in the order they are listed unless otherwise specifically allowed: a) the device shall drive a data word onto d[15:00]. b) the device shall generate a dstrobe edge to latch the new word no sooner than t dvs after changing the state of d[15:00]. the device shall generate a dstrobe edge no more frequently than t cyc for the selected ultra dma mode. the device shall not generate two rising or two falling dstrobe edges more frequently than 2t cyc for the selected ultra dma mode. c) the device shall not change the state of d[15:00] until at least t dvh after generating a dstrobe edge to latch the data. d) the device shall repeat steps (a), (b), and (c) until the data transfer is complete or an ultra dma data burst is paused, whichever occurs first. notes: d[15:00] and dstrobe signals are shown at both the host and the device to emphasize that cable settling time as well as cable propagation delay shall not allow the data signals to be considered stable at the host until some time after they are driven by the device.
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 18 host pausing an ultra dma data-in burst the host pauses a data-in burst by following the steps lettered below. a timing diagram is shown in below: ultra dma data-in burst host pause timing. the timing parameters are specified in page 12: ultra dma data burst timing requirements and are described in page 13: ultra dma data burst timing descriptions. the following steps shall occur in the order they are listed unless otherwise specifically allowed: (a) the host shall not pause an ultra dma data burst until at least one data word of an ultra dma data burst has been transferred. (b) the host shall pause an ultra dma data burst by negating -hdmardy. (c) the device shall stop generating dstrobe edges within t rfs of the host negating -hdmardy. (d) while operating in ultra dma modes 2, 1, or 0 the host shall be prepared to receive zero, one or two additional data words after negating -hdmardy. while operating in ultra dma modes 4 or 3 the host shall be prepared to receive zero, one, two or three additional data words. the additional data words are a result of cable round trip delay and t rfs timing for the device. (e) the host shall resume an ultra dma data burst by asserting -hdmardy. all waveforms in this diagram are shown with the asserted state high. negative true signals appear inverted on the bus relative to the diagram. notes: (1) the host may assert stop to request termination of the ultra dma data burst no sooner than t rp after -hdmardy is negated. (2) after negating -hdmardy, the host may receive zero, one, two, or three more data words from the device. (3) the bus polarity of the (-) dm arq and (-)dmack signals is dependent on the active interface mode.
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 19 device terminating an ultra dma data-in burst the device terminates an ultra dma data-in burst by following the steps lettered below. the timing diagram is shown in below: ultra dma data-in burst device termination timing. the timing parameters are specified in page 12: ultra dma data burst timing requirements and are described in page 13: ultra dma data burst timing descriptions. the following steps shall occur in the order they are listed unless otherwise specifically allowed: (a) the device shall not pause an ultra dma data burst until at least one data word of an ultra dma data burst has been transferred. (b) the device shall pause an ultra dma data burst by not generating dstrobe edges. (c) note ? the host shall not immediately assert stop to initiate ultra dma data burst termination when the device stops generating strobe edges. if the device does not negate dmarq, in order to initiate ultra dma data burst termination, the host shall negate -hdmardy and wait t rp before asserting stop. (d) the device shall resume an ultra dma data burst by generating a dstrobe edge. all waveforms in this diagram are shown with the asserted state high. negative true signals appear inverted on the bus relative to the diagram. notes: the definitions for the stop, hdmardy, and dstrob e signal lines are no longer in effect after dmarq and dmack are negated. a[02:00], -cs0 & -cs1 are true ide mode signal definitions.
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 20 host terminating an ultra dma data-in burst the host terminates an ultra dma data-in burst by following the steps lettered below. the timing diagram is shown in below: ultra dma data-in burst host termination timing. the timing parameters are specified in page 12: ultra dma data burst timing requirements and are described in page 13: ultra dma data burst timing descriptions. the following steps shall occur in the order they are listed unless otherwise specifically allowed: (a) the host shall not initiate ultra dma data burst termination until at least one data word of an ultra dma data burst has been transferred. (b) the host shall initiate ultra dma data burst termination by negating -hdmardy. the host shall continue to negate -hdmardy until the ultra dma data burst is terminated. (c) the device shall stop generating dstrobe edges within t rfs of the host negating -hdmardy (d) while operating in ultra dma modes 2, 1, or 0 the host shall be prepared to receive zero, one or two additional data words after negating -hdmardy. while operating in ultra dma modes 4 or 3 the host shall be prepared to receive zero, one, two or three additional data words. the additional data words are a result of cable round trip delay and t rfs timing for the device. (e) the host shall assert stop no sooner than t rp after negating -hdmardy. the host shall not negate stop again until after the ultra dma data burst is terminated. (f) the device shall negate dmarq within t li after the host has asserted stop. the device shall not assert dmarq again until after the ultra dma data burst is terminated. (g) if dstrobe is negated, the device shall assert dstrobe within t li after the host has asserted stop. no data shall be transferred during this assertion. the host shall ignore this transition on dstrobe. dstrobe shall remain asserted until the ultra dma data burst is terminated. (h) the device shall release d[15:00] no later than t az after negating dmarq. (i) the host shall drive d[15:00] no sooner than t zah after the device has negated dmarq. for this step, the host may first drive d[15:00] with the result of its crc calculation (see ata specification ultra dma crc calculation). (j) if the host has not placed the result of its crc calculation on d[15:00] since first driving d[15:00] during (9), the host shall place the result of its crc calculation on d[15:00] (see ata specification ultra dma crc calculation). (k) the host shall negate -dmack no sooner than t mli after the device has asserted dstrobe and negated dmarq and the host has asserted stop and negated -hdmardy, and no sooner than t dvs after the host places the result of its crc calculation on d[15:00]. (l) the device shall latch the host?s crc data from d[15:00] on the negating edge of -dmack. (m) the device shall compare the crc data received from the host with the results of its own crc calculation. if a miscompare error occurs during one or more ultra dma data burst for any one command, at the end of the command, the device shall report the first error that occurred (see ata specification ultra dma crc calculation) (n) while operating in true ide mode, the device shall release dstrobe within t iordyz after the host negates -dmack. (o) the host shall neither negate stop nor assert -hdmardy until at least t ack after the host has negated -dmack.
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 21 (p) in true ide mode, the host shall not assert -iord, -cs0, -cs1, nor a[02:00] until at least t ack after negating dmack. all waveforms in this diagram are shown with the asserted state high. negative true signals appear inverted on the bus relative to the diagram. notes: the definitions for the stop, hdmardy, and dstrob e signal lines are no longer in effect after dmarq and dmack are negated. a[02:00], -cs0 & -c s1 are true ide mode signal definitions.
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 22 initiating an ultra dma data-out burst an ultra dma data-out burst is initiated by following the steps lettered below. the timing diagram is shown in below: ultra dma data-out burst initiation timing. the timing parameters are specified in page 12: ultra dma data burst timing requirements and are described in page 13:ultra dma data burst timing descriptions. the following steps shall occur in the order they are listed unless otherwise specifically allowed: (a) the host shall keep -dmack in the negated state before an ultra dma data burst is initiated. (b) the device shall assert dmarq to initiate an ultra dma data burst. (c) steps (c), (d), and (e) may occur in any order or at the same time. the host shall assert stop. (d) the host shall assert hstrobe. (e) in true ide mode, the host shall not assert -cs0, -cs1, nor a[02:00]. (f) steps (c), (d), and (e) shall have occurred at least t ack before the host asserts -dmack.the host shall keep -dmack asserted until the end of an ultra dma data burst. (g) the device may negate -ddmardy t ziordy after the host has asserted -dmack. while operating in true ide mode, once the device has negated -ddmardy, the device shall not release -ddmardy until after the host has negated dmack at the end of an ultra dma data burst. (h) the host shall negate stop within t env after asserting -dmack. the host shall not assert stop until after the first negation of hstrobe. (i) the device shall assert -ddmardy within t li after the host has negated stop. after asserting dmarq and -ddmardy the device shall not negate either signal until after the first negation of hstrobe by the host. (j) the host shall drive the first word of the data transfer onto d[15:00]. this step may occur any time during ultra dma data burst initiation. (k) to transfer the first word of data: the host shall negate hstrobe no sooner than t ui after the device has asserted -ddmardy. the host shall negate hstrobe no sooner than t dvs after the driving the first word of data onto d[15:00].
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 23 all waveforms in this diagram are shown with the asserted state high. negative true signals appear inverted on the bus relative to the diagram. note: the definitions for the stop, ddmardy, and hstr obe signal lines are not in effect until dmarq and dmack are asserted. a[02:00], -cs0 & -cs1 are true ide mode signal definitions.
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 24 sustaining an ultra dma data-out burst an ultra dma data-out burst is sustained by following the steps lettered below. the timing diagram is shown in below: sustained ultra dma data-out burst timing. the associated timing parameters are specified in page 12: ultra dma data burst timing requirements and are described in page 13: ultra dma data burst timing descriptions. the following steps shall occur in the order they are listed unless otherwise specifically allowed: (a) the host shall drive a data word onto d[15:00]. (b) the host shall generate an hstrobe edge to latch the new word no sooner than t dvs after changing the state of d[15:00]. the host shall generate an hstrobe edge no more frequently than t cyc for the selected ultra dma mode. the host shall not generate two rising or falling hstrobe edges more frequently than 2t cyc for the selected ultra dma mode. (c) the host shall not change the state of d[15:00] until at least t dvh after generating an hstrobe edge to latch the data. (d) the host shall repeat steps (a), (b), and (c) until the data transfer is complete or an ultra dma data burst is paused, whichever occurs first. note: data (d[15:00]) and hstrobe signals are shown at bot h the device and the host to emphasize that cable settling time as well as cable propagation delay shall not allow the data signals to be considered stable at the device until some time after they are driven by the host.
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 25 device pausing an ultra dma data-out burst the device pauses an ultra dma data-out burst by following the steps lettered below. the timing diagram is shown in below: ultra dma data-out burst device pause timing. the timing parameters are specified in page 12: ultra dma data burst timing requirements and are described in page 13: ultra dma data burst timing descriptions. the following steps shall occur in the order they are listed unless otherwise specifically allowed: (a) the device shall not pause an ultra dma data burst until at least one data word of an ultra dma data burst has been transferred. (b) the device shall pause an ultra dma data burst by negating -ddmardy. (c) the host shall stop generating hstrobe edges within t rfs of the device negating -ddmardy. (d) while operating in ultra dma modes 2, 1, or 0 the device shall be prepared to receive zero, one or two additional data words after negating -hdmardy. while operating in ultra dma modes 4 or 3 the device shall be prepared to receive zero, one, two or three additional data words. the additional data words are a result of cable round trip delay and t rfs timing for the device. (e) the device shall resume an ultra dma data burst by asserting -ddmardy. all waveforms in this diagram are shown with the asserted state high. negative true signals appear inverted on the bus relative to the diagram. notes: (1) the device may negate dmarq to request termination of the ultra dma data burst no sooner than t rp after -ddmardy is negated. (2) after negating -ddmardy, the device may receive zero, one, two, or three more data words from the host.
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 26 device terminating an ultra dma data-out burst the device terminates an ultra dma data-out burst by following the steps lettered below. the timing diagram for the operation is shown in below: ultra dma data-out burst device termination timing. the timing parameters are specified in page 12: ultra dma data burst timing requirements and are described in page 13: ultra dma data burst timing descriptions. the following steps shall occur in the order they are listed unless otherwise specifically allowed: (a) the device shall not initiate ultra dma data burst termination until at least one data word of an ultra dma data burst has been transferred. (b) the device shall initiate ultra dma data burst termination by negating -ddmardy. (c) the host shall stop generating an hstrobe edges within t rfs of the device negating -ddmardy. (d) while operating in ultra dma modes 2, 1, or 0 the device shall be prepared to receive zero, one or two additional data words after negating -hdmardy. while operating in ultra dma modes 4 or 3 the device shall be prepared to receive zero, one, two or three additional data words. the additional data words are a result of cable round trip delay and t rfs timing for the device. (e) the device shall negate dmarq no sooner than t rp after negating -ddmardy. the device shall not assert dmarq again until after the ultra dma data burst is terminated. (f) the host shall assert stop within t li after the device has negated dmarq. the host shall not negate stop again until after the ultra dma data burst is terminated. (g) if hstrobe is negated, the host shall assert hstrobe within t li after the device has negated dmarq. no data shall be transferred during this assertion. the device shall ignore this transition of hstrobe. hstrobe shall remain asserted until the ultra dma data burst is terminated. (h) the host shall place the result of its crc calculation on d[15:00] (see ata specification ultra dma crc calculation). (i) the host shall negate -dmack no sooner than t mli after the host has asserted hstrobe and stop and the device has negated dmarq and -ddmardy, and no sooner than t dvs after placing the result of its crc calculation on d[15:00]. (j) the device shall latch the host?s crc data from d[15:00] on the negating edge of -dmack. (k) the device shall compare the crc data received from the host with the results of its own crc calculation. if a miscompare error occurs during one or more ultra dma data bursts for any one command, the device shall report the first error that occurred (see ata specification ultra dma crc calculation). (l) while operating in true ide mode, the device shall release dstrobe within t iordyz after the host negates -dmack. (m) the host shall not negate stop nor assert ?hdmardy until at least t ack after negating -dmack. (n) in true ide mode, the host shall not assert -iowr, -cs0, -cs1, nor a[02:00] until at least t ack after negating dmack.
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 27 all waveforms in this diagram are shown with the asserted state high. negative true signals appear inverted on the bus relative to the diagram. note: the definitions for the stop, ddmardy, and hstr obe signal lines are no longer in effect after dmarq and dmack are negated. a00-a02, -cs0 & -c s1 are true ide mode signal definitions.
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 28 host terminating an ultra dma data-out burst termination of an ultra dma data-out burst by the host is shown in below: ultra dma data-out burst host termination timing while timing parameters are specified in page 12: ultra dma data burst timing requirements and timing parameters are described in page 13: ultra dma data burst timing descriptions. the following steps shall occur in the order they are listed unless otherwise specifically allowed: (a) the host shall initiate termination of an ultra dma data burst by not generating hstrobe edges. (b) the host shall assert stop no sooner than t ss after it last generated an hstrobe edge.the host shall not negate stop again until after the ultra dma data burst is terminated. (c) the device shall negate dmarq within t li after the host asserts stop. the device shall not assert dmarq again until after the ultra dma data burst is terminated. (d) the device shall negate -ddmardy within t li after the host has negated stop. the device shall not assert -ddmardy again until after the ultra dma data burst termination is complete. (e) if hstrobe is negated, the host shall assert hstrobe within t li after the device has negated dmarq. no data shall be transferred during this assertion. the device shall ignore this transition on hstrobe. hstrobe shall remain asserted until the ultra dma data burst is terminated. (f) the host shall place the result of its crc calculation on d[15:00] (see ata specification ultra dma crc calculation). (g) the host shall negate -dmack no sooner than t mli after the host has asserted hstrobe and stop and the device has negated dmarq and -ddmardy, and no sooner than t dvs after placing the result of its crc calculation on d[15:00]. (h) the device shall latch the host?s crc data from d[15:00] on the negating edge of -dmack. (i) the device shall compare the crc data received from the host with the results of its own crc calculation. if a miscompare error occurs during one or more ultra dma data bursts for any one command, at the end of the command, the device shall report the first error that occurred (see ata specification ultra dma crc calculation). (j) while operating in true ide mode, the device shall release -ddmardy within t iordyz after the host has negated -dmack. (k) the host shall neither negate stop nor negate hstrobe until at least t ack after negating -dmack. (l) in true ide mode, the host shall not assert -iowr, -cs0, -cs1, nor a[02:00] until at least t ack after negating dmack..
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 29 all waveforms in this diagram are shown with the asserted state high. negative true signals appear inverted on the bus relative to the diagram. notes: the definitions for the stop, ddmardy, and hstrob e signal lines are no longer in effect after dmarq and dmack are negated. a[02:00], -cs0 & -c s1 are true ide mode signal definitions.
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 30 identify device information the identify device command enables the host to receive parameter information from the device. this command has the same protocol as the read sector(s) command. the parameter words in the buffer have the arrangement and meanings defined in table as below. all reserved bits or words are zero. hosts should not depend on obsolete words in identify device containing 0. table below specifies each field in the data returned by the identify device command. in table as below, x indicates a numeric nibble value specific to the card and aaaa indicates an ascii string specific to the particular drive. word address default value total bytes data field type information 0 044ah 2 general configuration ? bit significant with ata-4 definitions. 1 xxxxh 2 default number of cylinders 2 0000h 2 reserved 3 00xxh 2 default number of heads 4 0000h 2 obsolete 5 0000h 2 obsolete 6 xxxxh 2 default number of sectors per track 7-8 xxxxh 4 number of sectors per card (word 7 = msw, word 8 = lsw) 9 xxxxh 2 obsolete 10-19 aaaa 20 serial number in ascii (right justified) 20 0000h 2 obsolete 21 0000h 2 obsolete 22 0004h 2 number of ecc bytes passed on read/write long commands 23-26 aaaa 8 firmware revision in asc ii. big endian byte order in word 27-46 aaaa 40 model number in ascii (left justifi ed) big endian byte order in word 47 xxxxh 2 maximum number of sectors on read/write multiple command 48 0000h 2 reserved 49 xx00h 2 capabilities 50 0000h 2 reserved
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 31 word address default v alue total b y tes data field type information 51 0200h 2 pio data transfer cycle timing mode 52 0000h 2 obsolete 53 000xh 2 field validity 54 xxxxh 2 current numbers of cylinders 55 xxxxh 2 current numbers of heads 56 xxxxh 2 current sectors per track 57-58 xxxxh 4 current capacity in sectors (lbas)(word 57 = lsw, word 58 = msw) 59 01xxh 2 multiple sector setting 60-61 xxxxh 4 total number of sectors addressable in lba mode 62 0000h 2 reserved 63 0x0xh 2 multiword dma transfer. in pc card modes this value shall be 0h 64 0003h 2 advanced pio modes supported 65 xxxxh 2 minimum multiword dma transfer cycle time per word. in pc card modes this value shall be 0h 66 xxxxh 2 recommended multiword dma transfer cycle time. in pc card modes this value shall be 0h 67 xxxxh 2 minimum pio transfer cycle time without flow control 68 xxxxh 2 minimum pio transfer cycle time with iordy flow control 69-79 0000h 20 reserved 80-81 0000h 4 reserved ? cf cards do not return an ata version 82-84 xxxxh 6 features/command sets supported 85-87 xxxxh 6 features/command sets enabled 88 001fh 2 ultra dma mode supported and selected (udma mode 0 ~ 4) 89 xxxxh 2 time required for security erase unit completion 90 xxxxh 2 time required for enhanced security erase unit completion 91 xxxxh 2 current advanced power management value 92-127 0000h 72 reserved 128 xxxxh 2 security status 129-159 0000h 64 vendor unique bytes 160 xxxxh 2 power requirement description 161 0000h 2 reserved for assignment by the cfa 162 0000h 2 key management schemes supported 163 xxxxh 2 cf advanced true ide timing mode capability and setting 164 xxxxh 2 cf advanced pc card i/o and memory timing mode capability 165-167 0000h 6 reserved for assignment by the cfa 168-255 0000h 158 reserved
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 32
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 33 capacity specifications: transcend p/n capacity cylinder (c) head (h) sector (s) TS128MDOM40V-S 128mb 248 16 63 ts256mdom40v-s 256mb 496 16 63 ts512mdom40v-s 512mb 993 16 63 ts1gdom40v-s 1gb 1942 16 63 ts2gdom40v-s 2gb 3884 16 63 ts4gdom40v-s 4gb 7769 16 63 ts8gdom40v-s 8gb 15538 16 63 ts16gdom40v-s 16gb 33149 15 63
t t t r r r a a a n n n s s s c c c e e e n n n d d d 4 4 4 0 0 0 - - - p p p i i i n n n i i i d d d e e e f f f l l l a a a s s s h h h m m m o o o d d d u u u l l l e e e t t t s s s 1 1 1 2 2 2 8 8 8 m m m ~ ~ ~ 1 1 1 6 6 6 g g g d d d o o o m m m 4 4 4 0 0 0 v v v - - - s s s transcend information inc. ver 1.2 34 ordering information the above technical information is based on industry standard data and has been tested to be reliable. however, transcend makes no warranty, either expressed or implied, as to its accura cy and assumes no liability in co nnection with the use of this product. transcend reserves the right to make changes to the specifications at any time without prior notice. usa los angeles: e-mail: sales@transcendusa.com maryland : e-mail: sales_md@transcendusa.com www.transcendusa.com china e-mail: sales@transcendchina.com www.transcendchina.com germany e-mail: vertrieb@transcend.de www.transcend.de hong kong e-mail: sales@transcend.com.hk www.transcendchina.com japan e-mail: sales@transcend.co.jp www.transcend.jp the netherlands e-mail: sales@transcend.nl www.transcend.nl taiwan no.70, xingzhong rd., neihu di st., taipei, taiwan, r.o.c tel +886-2-2792-8000 fax +886-2-2793-2222 e-mail: sales@transcend.com.tw www.transcend.com.tw united kingdom e-mail: sales@transcend-uk.com www.transcend-uk.com ts xxxx dom 40 v-s pin count: 40 = 40 pin 44 = 44 pin capacity: 128m-512m = 128 mb up to 512 mb 1g-16g = 1 gb up to 16 gb ide flash module (disk on module) transcend product type: v = vertical h = horizontal

▲Up To Search▲

Price & Availability of TS128MDOM40V-S

	To Download TS128MDOM40V-S Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .